300-360試験,概要,300-360受験記対策,300-360難易度,300-360ITパスポート

CiscoCCNP Wireless認定資格300-360試験問題集はIT資格試験の模擬問題がWebベースで学習できる、IT自分戦略研究所の新サービスの関連資格をテーマとして取り上げています 。CiscoCCNP Wireless認定資格Designing Cisco Wireless Enterprise Networks試験問題集を持って、関する問題を解決できると証明できます。人気の問題集の使用は認定を取得ばかりでなく、自分の知識が高くなります。Killtest300-360試験問題集を使って、IT資格認証試験は一回で合格することを保証します。 CCNP Wireless資格を取得するために、資格はグローバルに認識される業界トップの認定資格と試験を提供します。KilltestのCCNP Wireless認定資格の300-360試験問題集は現在、市場上で一番質のいい学習教材です。
Share some CCNP Wireless 300-360 exam questions and answers below.
A network engineer is preparing for an office site survey with a height of 2.5 meters.

Which three components are recommended to complete the survey? (Choose three.)

A. Use APs with external antennas.

B. Use DoS attack on APs while measuring the throughput.

C. Use APs with built-in antennas.

D. Use a battery pack to power APs.

E. Use a drawing of the office space to draw AP and client placements.

F. Use APs with directional antennas.

Answer: C,D,E

A Cisco 7925 phone at a client’s location is not registering with CUCM. The engineer analyzes a packet capture, sees that the phone receives an IP, and downloads the proper configuration file from TFTP successfully. What type of messages should the phone be sending at this point?

A. H.245

B. H.323

C. MCGP

D. SCCP

Answer: D

Which two options describe best practices that must be completed after a wireless installation is finished? (Choose two.)

A. Make sure that there are no spaces between the devices on the rack that the Wireless Lan Controller isinstalled.

B. Consult with the customer to ensure that the IT staff has a complete set of design and installationdocuments.

C. Make sure the customer is aware that they should consider purchasing a support contract immediately afterthe installation is complete.

D. Spend time with the customer to show them the controller GUI and inform them how they can reach theCisco TAC if they have any problems.

E. Test all the customer’s wireless devices and applications to ensure they are working properly.

Answer: B,E

The AP has been configured property for a VoWLAN survey The RF environment contains a noise of -87 to -90 dBm. What is the target value for the cell edge reading?

A. -62 dBm

B. -67 dBm

C. -60 dBm

D. -70 dBm

Answer: A

An 802.11n implementation is being discussed. Users are satisfied with the potential 300­450 Mbps throughput of new 802.11n APs.

Which three bandwidth requirements are used to calculate per client bandwidth through an 802.11n AP network? (Choose three.)

A. 450 Mbps throughput is the client max for 5-GHz radio.

B. Channel bonding on 5 GHz is required for a client to have a 300 Mbps WiFi link.

C. 300 Mbps throughput is the client max for 2.4-GHz radio.

D. The remaining bandwidth is divided per device when more clients are connected to one AP.

E. 100 Mbps Ethernet switch port is a potential bottleneck.

F. Clean Air helps clear noise for 802.11n channel bonding to work.

Answer: A,C,E

A Cisco 7925 phone at a client¡¯s location is not registering with CUCM. The engineer analyzes a packet capture, sees that the phone receives an IP, and downloads the proper configuration file from TFTP successfully.

What type of messages should the phone be sending at this point?

A. H.245

B. H.323

C. MCGP

D. SCCP

Answer: D

An engineer is performing a predictive wireless design for a medical treatment environment, which requires data and voice services.

Which of the following is a requirement for the design?

A. overlapping -72 dBm coverage from two access points

B. overlapping -67 dBm coverage from two access points

C. continuous -67 dBm coverage from one access point

D. continuous -72 dBm coverage from one access point

Answer: C

What is a common cause for signal attenuation?

A. Cinder block wall

B. Office window

C. Metal door

D. Glass wall

Answer: C

An engineer is performing a predictive wireless design for a carpeted office space, which requires voice capability and location services.

Which two requirements are inputs to the design? (Choose two.)

A. overlapping -67 dBm coverage from three access points

B. overlapping -75 dBm coverage from three access points

C. overlapping-72 dBm coverage from two access points

D. continuous -67 dBm coverage from one access pointe. continuous -72 dBm coverage from one access point

Answer: BD

An engineer must design wireless coverage in thick-walled stairwells.

Which information should the engineer refer to when determining where APs can be installed?

A. Local or National Building Code

B. IEEE

C. BICSI TDMM

D. Cisco Hardware Installation Guide

Answer: A

CCNP Wireless資格技術者認定制度は、国際的に通用する高度な技術力の証として、専門知識と経験の深さを全世界共通の基準で測り認定する資格制度です。このごろ、CiscoCCNP Wireless資格認定300-360試験参考書に関心を示すようになってきたのでなんだかんだネットを探してみるようになりました。従来技術者認定制度に対してはそんなには関心がなかった部分もあったけど随分ウェブ上に記事があるものですね。CiscoCCNP Wireless資格認定Designing Cisco Wireless Enterprise Networks試験参考書は数年間の経験があり、勤勉な認定された一流のIT専門家に支えられます。

近年、IT技術の急速な発展に伴って、IT技術を勉強し始める人がますます多くなっています。そこで、IT業界で働く人も多くなっています。このように、IT業界の競争が一層激しくなります。同様にIT業界で働いていて、IT夢を持っているあなたは、きっと他の人にキャッチアップされ、追い抜かれることを望まないでしょう。それでは、ずっと自分自身のスキルをアップグレードすることが必要になり、他の人に自分の強さを証明する必要があります。では、どうやって自分の能力を証明するのですか。